Good Afternoon
Arthur, I am not an expert on G32 results, how whacked is this reading below ?Thanks

Connecting...
Printer is now online.
Using tool 0.
>>> G32
SENDING:G32
Calibrating Endstops: target 0.030000mm, radius 120.000000mm
set trim to X:0.000000 Y:0.000000 Z:0.000000
initial Bed ht is 591.162476 mm
T1-0 Z:4.7375 C:379
T2-0 Z:4.8875 C:391
T3-0 Z:5.2750 C:422
set trim to X:0.000000 Y:-0.187830 Z:-0.673057
T1-1 Z:4.9625 C:397
T2-1 Z:4.9750 C:398
T3-1 Z:5.0500 C:404
set trim to X:0.000000 Y:-0.203482 Z:-0.782625
T1-2 Z:5.0000 C:400
T2-2 Z:5.0250 C:402
T3-2 Z:5.0875 C:407
set trim to X:0.000000 Y:-0.234787 Z:-0.892193
T1-3 Z:5.0375 C:403
T2-3 Z:5.0250 C:402
T3-3 Z:4.9875 C:399
set trim to X:-0.062610 Y:-0.281744 Z:-0.892193
T1-4 Z:5.0250 C:402
T2-4 Z:5.0250 C:402
T3-4 Z:4.9875 C:399
set trim to X:-0.109567 Y:-0.328702 Z:-0.892193
T1-5 Z:5.0250 C:402
T2-5 Z:5.0125 C:401
T3-5 Z:5.0375 C:403
trim set to within required parameters: delta 0.025000
Calibrating delta radius: target 0.030000, radius 120.000000
initial Bed ht is 591.212463 mm
CT Z:5.000 C:400
T1-1 Z:4.950 C:396
T2-1 Z:4.950 C:396
T3-1 Z:5.225 C:418
C-1 Z-ave:5.0417 delta: -0.042
Setting delta radius to: 204.6708
T1-2 Z:4.938 C:395
T2-2 Z:4.938 C:395
T3-2 Z:4.988 C:399
C-2 Z-ave:4.9542 delta: 0.046
Setting delta radius to: 204.7854
T1-3 Z:4.963 C:397
T2-3 Z:4.975 C:398
T3-3 Z:5.037 C:403
C-3 Z-ave:4.9917 delta: 0.008
Calibration complete, save settings with M500

Connecting...
Printer is now online.
Using tool 0.
>>> G32
SENDING:G32
Calibrating Endstops: target 0.030000mm, radius 120.000000mm
set trim to X:0.000000 Y:0.000000 Z:0.000000
initial Bed ht is 591.162476 mm
T1-0 Z:4.7375 C:379
T2-0 Z:4.8875 C:391
T3-0 Z:5.2750 C:422
set trim to X:0.000000 Y:-0.187830 Z:-0.673057
T1-1 Z:4.9625 C:397
T2-1 Z:4.9750 C:398
T3-1 Z:5.0500 C:404
set trim to X:0.000000 Y:-0.203482 Z:-0.782625
T1-2 Z:5.0000 C:400
T2-2 Z:5.0250 C:402
T3-2 Z:5.0875 C:407
set trim to X:0.000000 Y:-0.234787 Z:-0.892193
T1-3 Z:5.0375 C:403
T2-3 Z:5.0250 C:402
T3-3 Z:4.9875 C:399
set trim to X:-0.062610 Y:-0.281744 Z:-0.892193
T1-4 Z:5.0250 C:402
T2-4 Z:5.0250 C:402
T3-4 Z:4.9875 C:399
set trim to X:-0.109567 Y:-0.328702 Z:-0.892193
T1-5 Z:5.0250 C:402
T2-5 Z:5.0125 C:401
T3-5 Z:5.0375 C:403
trim set to within required parameters: delta 0.025000
Calibrating delta radius: target 0.030000, radius 120.000000
initial Bed ht is 591.212463 mm
CT Z:5.000 C:400
T1-1 Z:4.950 C:396
T2-1 Z:4.950 C:396
T3-1 Z:5.225 C:418
C-1 Z-ave:5.0417 delta: -0.042
Setting delta radius to: 204.6708
T1-2 Z:4.938 C:395
T2-2 Z:4.938 C:395
T3-2 Z:4.988 C:399
C-2 Z-ave:4.9542 delta: 0.046
Setting delta radius to: 204.7854
T1-3 Z:4.963 C:397
T2-3 Z:4.975 C:398
T3-3 Z:5.037 C:403
C-3 Z-ave:4.9917 delta: 0.008
Calibration complete, save settings with M500

https://drive.google.com/file/d/0Bw_bGIRErnhmejU5Ul9Db1NpNDQ/view?usp=sharing

Five Foot Delta printing a shark, blue tape, no heat on bed, PLA SMOOTHIE RULES !!

Does anyone have all of the code changes Marlin needs for a RAMPS 1.4 board and BLTouch? I have a Smoothie and BLTouch works perfect.
I have THREE Marlin/RAMPS 1.4 printers and none of them work completely correctly. Most of what I find online, even in Marlin RC version, makes it look like G29 may not be completely fixed. Is that so ?? I dont see anyone on BLTouch page saying they have Marlin trouble, so it may be that I am missing something in the code.
Please anyone ? I have done all of the changes shown on BLTouch pages since day one, and Marlin has never worked correctly
Thanks in Advance

What on earth did they do to Google Hangouts, it has never sucked more. Everything on my PC reconnects every time, and hangouts keeps telling me I am not on the internet, even as I type and post this, Thanks Google, I am sure this will work nicely as a tech support tool HA HA

Normal behavior if BLTouch is on the deck and the M280 was not issued at start of print job

Ok how do I post a ZIP file with the Marlin RC files that actually work with BLTouch ??
I was asked to post them but apparently I don't know how.

Five Foot Deltas and BLTouch installed

BLTOUCH ...Hopefully this is what folks have been asking me for.
The photo attached will need my explanation  just a tiny bit.
My Delta is five feet tall..so the wires changed colors on the way back to Smoothie.
Here is what makes BLTouch seem hard to figure out. The TWO and THREE pin connectors they supply need to be separated into a different group.
If you are not using MIN endstops, it does not matter which set of pins you use for signal from BLTouch back to Smoothie Servo module, so with that said...this is my color conversion chart...sorry
BLTouch WHITE wire to Smoothie RED wire in photo
BLTouch BLACK wire to Smoothie Black wire in photo
BLTouch ORANGE wire to Smoothie GREY in photo
BLTouch RED wire to Smoothie GREEN in photo
BLTouch BROWN wire to Smoothie BROWN in photo..(oops)

 ZMin sees the BLTouch as a simple switch ( I think)
So ZMIN Pin 1.28 and GROUND right next to it are your switch terminals for SMOOTHIE input

I then went to XMin terminals to effect control and supply power to BLTouch.
Pin 1.24 is the switch output pin, so Smoothie communicates with BLTouch on that pin, (grey wire in picture)
Next to that is simply power and ground so BLTouch can self test and operate it's tiny parts

Once you do all of this , M280 activates (rasies) the BLTouch pin
M281 deactivates (lowers) the BLTouch pin.
You have to add start and end scripts .
Start script for every print needs M280 as a single line
End Script for every print needs M281 as a single line
I know BLTouch tells you with PWM you can reset the BLTouch, but I have found that I am miles ahead to simply reboot the board, power reset performs the BLTouch self test and puts it in the proper state...and has been more reliable for me.
To each his own on that part.
I spent a few days trying BLTouch as a PWM device on Smoothie, and I may just not know how to make it work, but it was erratic at best. The day I made it digital in the servo module it worked perfectly



If you figured out my color conversion above, the next step is below
Do this to your servo module.

# Switch module for servo control
switch.servo.enable                            true             #
switch.servo.input_on_command                  M280             # M280 S7.5 would be midway
switch.servo.input_off_command                 M281             # same as M280 S0 0% duty cycle, effectively off
switch.servo.output_pin                        1.24           # must be a PWM capable pin
switch.servo.output_type                       digital              # H/W pwm output settable with S parameter in the input_on_comand
#switch.servo.pwm_period_ms                    20               # set period to 20ms (50Hz) default is 50Hz

# optional Z probe
gamma_min_endstop                           nc               # normally 1.28. Change to nc to prevent conflict,
zprobe.enable                                true            # set to true to enable a zprobe
zprobe.probe_pin                             1.28            # pin probe is attached to if NC remove the !
zprobe.slow_feedrate                         5               # mm/sec probe feed rate
zprobe.debounce_count                       100              # set if noisy
zprobe.fast_feedrate                         200             # move feedrate mm/sec
zprobe.probe_height                          5               # how much above bed to start probe


# associated with zprobe the leveling strategy to use
leveling-strategy.delta-calibration.enable   true            # basic delta calibration
leveling-strategy.delta-calibration.radius   120             # the probe radius
#the initial height above the bed we stop the intial move down after home to find the bed
#this should be a height that is enough that the probe will not hit the bed and is an offset from gamma_max (can be set to 0 if gamma_max takes into account the probe offset)
leveling-strategy.delta-calibration.initial_height 10 # height above bed to stop initial move

That is all I have,, good luck, this works for me very well.
Don't forget to M500 the settings after you run G32 on your delta !
BTW prints height is currently 607.49 mm with a one and a half  inch heater assmbly, print diameter is set to 300 mm

So my question is, why has every PC I use, and that is about 6 desktops, two windows tablets and an Ultrabook, started crashing , needing addons re-enabled, logging me out, and not logging me in automatically when I use Google Chrome, in the last three weeks?  
Google Voice, Google Play, Google Mail, everything associated with my Google Chrome?  So I installed Firefox and what do you know, everything works all day, every day for days in a row. Why isnt there a way to tell Google they have a problem ? Maybe I missed this, but I cant find contact info anywhere and I am going blind reading stupid forums with nothing even close to this issue in them...anyone ?