Phone Orders or Help: 800-734-3588, 206-458-7550 (Pacific Time)

Home > Electronics

DIY 3D Printer Electronic Parts

Having Trouble Ordering?

Please call: 800-734-3588 206-458-7550

Shipping Charges Too High?

We will refund your PayPal account.
Or you can for a correct PayPal invoice.

Nema 17 Stepper Motor XYZ

Manufacturer's Part Number 1124090

See Nema 17 Stepper Motor Diagram

High Torque: 5.5 kg-cm, 53.9 N-cm, 76 oz-in, 4.77 lb-in

4.2 Volt, 1.5 Amp, 1.8 deg per step

23 mm long, 5 mm Shaft with D Cut

Wires are 750 mm to the tip of the connector

Model: 42BYGH4803

2 Phase

200 Steps per Revolution

Resistance per Phase 2.8 Ohms

Inductance 4.8 mH

Class B Insulation

Kysan Electronics

DIY 3D Printer Electronic Parts For Sale

1 / $16.65

3 / $50.00

4 / $65.00

5 / $80.00

Nema 17 Geared Stepper Motor

Manufacturer's Part Number 1040229

See Nema 17 Geared Stepper Motor Diagram

42 mm

Gear Ratio: 5.18:1

1830 mm Wire Connector

Wires are 1830 mm to the tip of the connector

20 mm long, 8 mm Shaft with D Cut

Step Angle: 1.8°

Rated Voltage: 2.4 V

Rated Current: 1.0 A

2 Phase

Inductance per Phase: 3.5 mH ±20% Phase

Resistance per Phase 2.4 Ohms ±10% Phase

Holding Torque: 2.2 Kg.cm

Class B Insulation

Diameter of the Geared Housing = 36 mm

Diameter of the Mounting Holes = 2 mm

Kysan Electronics

$33.95

Vibration Dampers

For use with Nema 17 stepper motors.

Significantly reduces noise, vibration and resonance problems commonly found in stepper motors

Robust but lightweight

Threaded mounting holes; can be mounted directly onto the motor flange

2.2 mm access hole, large enough to accommodate a spigot and gear or pulley

6 mm thick

Does not fit geared stepper motor

Steel and Rubber Vibration Dampers

Manufacturer's Part Number MY17RMDAMP
.

Quantities 1, 3, 4, 5

For use with Nema 17 stepper motors.

Helps reduces noise, vibration and resonance problems commonly found in stepper motors

Helps prevent thermal transfer from motor to plastic parts

Mounting holes; can be mounted directly onto the motor flange

2.2 mm access hole, large enough to accommodate a spigot and gear or pulley

3 mm thick

Does not fit geared stepper motor

Cork Vibration Dampers

Quantities 1, 3, 4, 5

Power Supply

Mean Well Switching Power Supply

Model: S-350-12

Specifications

Manufacturer: Mean Well

Output Power: 348 W

Input Voltage: 90 VAC to 132 VAC, 254 VDC to 370 VDC

Number of Outputs: 1

Output Voltage-Channel 1: 12 V

Output Current-Channel 1: 29 A

150 mV p-p Noise

83 % efficient

0.5 % Load Stability

Dimensions: 215mm x 115mm x 50mm

Mounting Style: Chassis

Data Sheet

$39.95

24 Volt 400W Wei Hao Single Output Power Supply

Model: S-400-24

Specifications

Manufacturer: Wei Hao (W H)

Single Output: 400W

16.5 Amps at 24 V

150 mV p-p Noise

0.5 % Load Stability

Selectable by Switch

Dimensions: 215mm x 115mm x 50mm

Data Sheet

$39.95

Mean Well 150W Single Output with PFC Function

Model MW SP-150 15

Features

Universal AC input / Full range

Built-in active PFC function, PF>0.93

Protections: Short circuit / Overload / Over voltage / Over temperature

Built-in constant current limiting circuit

LED indicator for power on

100% full load burn-in test

Specifications

Manufacturer: Mean Well

15V 150W

10 Amps at 15 V

Noise: 100 mV p-p

Approvals: UL60950-1

Product: Switching Supplies

Open Frame/Enclosed: Enclosed

Output Power Rating: 150 W

Input Voltage: 90 VAC to 264 VAC, 254 VDC to 370 VDC

Number of Outputs: 1 Output

Output Voltage-Channel 1: 15 VDC

Commercial/Medical: Commercial

Mounting Style: Chassis

Dimensions: 179mm x 99mm x 45mm

Series: SP-150

Data Sheet

$39.95

LED
Specifications Quantity: 10 Size: 5mm Wire Length: 20 cm Forward Voltage: 12V/DC Light Color: White	Picture Coming $5.95

Kapton Heater
Specifications: Lead Length: 1000 mm Lead Wire: High Temperature Teflon Lead Location: Center Thermistor: 100K QWG-104F-3950 Preferred Thermistor Location: Center with 1000 mm Leads Resistance was measured at room temperature 1 cm Hole in Center Adhesive On Back
Thermistor Specifications: 100K Thermistor +/ 1 percent B = 3950K Operating Temp Range -35° C to 300° C
Item 1-1 Resistance	Particulars Resistance AT25° C	R25	100K Ohm ±1%
1-2 B Constant	In(R25/R50) B= =(K) (T/T50-1/T25)	R25/50	3950K ±1%
1-3 Operating Temperature Range			-35° C to 300° C
24 v Kapton Heater - 400 mm Round Size: 398 mm Use with 400 mm Borosilicate Glass Voltage: 24 Watts: ~240 Amps: ~10 Resistance: ~2.9 ohms cold Needs a heat spreader		Wires Included Need to be attached $44.95
24 v Kapton Heater - 350 mm Round Size: 348 mm Use with 350 mm Borosilicate Glass Voltage: 24 Watts: ~240 Amps: ~10 Resistance: ~2.9 ohms cold Needs a heat spreader		Wires Included Need to be attached $39.95
24 v Kapton Heater - 300 mm Round Size: 298 mm Use with 300 mm Borosilicate Glass Voltage: 24 Watts: ~240 Amps: ~10 Resistance: ~2.9 ohms cold Needs a heat spreader		$34.95
24 v Kapton Heater - 240 mm Round Size: 240 mm Use with 250 mm Borosilicate Glass Voltage: 24 Watts: ~240 Amps: ~10 Resistance: ~2.9 ohms cold		$29.95
12 v Kapton Heater - 240 mm Round Size: 240 mm Use with 250 mm Borosilicate Glass Voltage: 12 Watts: ~120 Amps: ~10 Resistance: ~1.2 ohms cold		$29.95
24 v Kapton Heater - 160 mm Round Size: 160 mm Use with 170 mm Borosilicate Glass Voltage: 24 Watts: ~240 Amps: ~10 Resistance: ~2.9 ohms cold		$24.95
12 v Kapton Heater - 160 mm Round Size: 160 mm Use with 170 mm Borosilicate Glass Voltage: 12 Watts: ~120 Resistance: ~1.2 ohms cold		$24.95

Cork Heated Bed Insulator

Specifications:

170 mm diameter
2 1/2 mm thick
Adhesive back

Picture Coming

$9.95

Aluminum Heat Spreaders
199 mm x 213 mm Picture Coming	$11.95
168 mm Picture Coming	$11.95
248 mm Picture Coming	$16.95
298 mm Picture Coming	$21.95
348 mm Picture Coming	$26.95
398 mm Picture Coming	$32.95

FSR - Force Sensitive Resistor

Description

Varies its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance

When no pressure is being applied to the FSR, its resistance will be larger than 1M Ohm

Can sense applied force in the range of 100g-10kg

Two pins extend from the bottom of the sensor

0.1" pitch

Bread board friendly

Peel-and-stick rubber backing on the other side of the sensing area to mount the FSR

Long Tail

1 / $6.95
2 / $13.50
3 / $19.95
4 / $25.25
5 / $29.95

Tail: 1.75"

Overall length: 2.375"

Overall width: 0.75"

Sensing diameter: 0.5"

Short Tail

Diagram

1 / $6.95
2 / $13.50
3 / $19.95
4 / $25.25
5 / $29.95

Tails: 0.5"

Overall length: 1.25"

Overall width: 0.75"

Sensing diameter: 0.5"

Board - FSR Endstop Controller

By John SL

Version 1.2
Dimensions: 1 1/8" x 1"

For more information, see FSR Endstop Controller.

$10.00

FSR Endstop Controller Kit

Contains:

(3) Long Tail FRSs
(1) FSR Endstop Controller

$29.95

Contains:

(3) Short Tail FRSs
(1) FSR Endstop Controller

$29.95

End Stops, Limit Switch

Switch Detector 5 mm with Mtg Hole

Lead free / RoHS Compliant

Snap Action, Limit Switch

Switch Function: Off-Mom

Contact Rating @ Voltage: 0.01A @ 5VDC

Actuator Type: Overtravel Plunger

Mounting Type: Chassis Mount

Termination Style: Solder Lug

Operating Force: 35gf

End Stops, Limit Switch

5 mm with Mtg Hole

Manufacturer Part Number: ESE-11HS2

3 / $6.95

SPDT

Single Pole

19.8 x 10.2 x 6.4 mm (0.78" x 0.40" x 0.25")

125/30 VAC/VDC

10.1 A @ 125 VAC/250 VAC

10.1 A @ 8 VDC/14 VDC

4 A @ 30 VDC

150 g operating force

2.4 mm hole size

CSA Certified

30 Million Operations Minimum

End Stop, Limit Switch

Switch Pin Plunger
10.2 mm with Mtg Holes

Manufacturer Part Number: SS-5

2 / $5.50

3 / $6.95

4 / $7.95

Wiring

Molex 2510 / 2510T compatible pin connectors

Compatible with PrintrBoard Electronics

Ends are pre-stripped and tinned

0.100" centers

Female connectors for Printrboard

600 mm total length (wire + connector)

2 Pin

4 / $5.95

Out of Stock

3 Pin

3 / $5.95

Out of Stock

4 Pin

3 / $5.95

Out of Stock

Wiring Components - Connectors

Molex 2510/2510-T Compatible

0.100" centers

For Printrboard

Female

2 Pin

10 / $4.95

3 Pin

10 / $4.95

4 Pin

10 / $4.95

Wiring Components - Crimp Pins

Molex 2510/2510-T Compatible

100 / $5.95

Teflon Coated Wire

Can Withstand High Heat

Voltage Rating: 600 Volts

Insulation Material: Teflon

19 Strands

Wire Gauge: 16 AWG

M16878 / 4BJE9

Choose Color (White/Black)

1 meter / $5.95

Wire Gauge: 18 AWG

Conductors: 1

Mil-W-16878/4 (Type E)
200C 600 V RMS

Choose Color (Green/Yellow)

1 meter / $5.95

Silicone Rubber Coated Wire

Red

18 AWG

150° C

TV-3

ATX 12 Volt Power Connector and Crimp Pins
Use to connect power to PrintrBoard Not needed if PC power supply has a 12 volt connector Includes 2 Connectors 10 Crimp Pins	$4.95

USBtinyISP Programmer with USB Cable

$17.95

Open source v3 USB AVR programmer and SPI interface

Works with AVRdude

AVRStudio compatible for use with Windows, Linux, and Mac OS X

Based off of the USBtiny design that has been improved to use the SpokePOV interface

Includes:

Fully functioning pre-programmed USBtinyISP v3 board

USB cable

10 pin programming cable

6 pin programming cable

Easy to use:

AVRdude compatible

USB drivers available for Windows using libusb. No driver needed for Mac OS X or Linux

Power/USB good LED

Busy LED

Buffered I/O for variable voltage targets 2V-6V (Remember to take out the 5 volt power jumper)

Easy to power:

Can use USB power if less than 100mA is required