Embedded Artists' LPC1788 Developer's Kit lets you get up-and-running quickly with the LPC1788 OEM Board. The LPC1788 OEM Board is equipped with NXP's Cortex-M3 based LPC1788 microcontroller suitable for a wide range of applications that requires advanced communication and high quality graphic displays.
NXP's Cortex-M3 LPC1788 microcontroller in BGA package
Program Flash
128 MB NAND FLASH + 512 kB internal
Data Memory
32 MB SDRAM + 96 KB internal 32- or 16-bit data bus to SDRAM Note: The Developer's Kit initially only offer the 32-bit databus version.
Ethernet
100/10M Ethernet interface based on SMSC LAN8720 Ethernet PHY
Clock Crystals
• 12.000 MHz crystal for CPU
• 32.768 kHz crystal for RTC
Dimensions
66 x 48 mm
Power
• +3.3V powering
Connectors
• 200 pos expansion connector (as defined in SODIMM standard), 0.6mm pitch
Temperature Range
-40 to +85 degrees Celsius (applies to rev D of the board and later)
Other
• 256 Kbit I2C E2PROM for storing non-volatile parameters
• Buffered 32- or 16-bit databus
OEM Base Board
Connectors and Interfaces
• 200 pos, 0.6mm pitch SODIMM connector for OEM Board
• LCD expansion connector with control signals for touch screen interface
• Expansion connector with all OEM Board signals
• Ethernet connector (RJ45)
• CAN interface & connector (provision for second CAN interface, but not mounted)
• MMC/SD interface & connector
• USB1: OTG or Host interface & connector
• USB2: Device or Host interface & connector
• Provision for NXP JN5148 RF module (former Jennic) interface (RF module not included)
• Full modem RS232 (cannot be fully used on 32-bit databus OEM boards)
• RS422/485 interface & connector
• Provision for IrDA transceiver interface (transceiver not mounted)
• I2S audio codec (mic in, line in, line out, headphone out) • SWD/JTAG connector
• Trace connector and pads for ETM connector
• Serial Expansion Connector, 14-pos connector with UART/I2C/SPI/GPIO pins
Power
• Power supply, either via USB or external 5V DC
• Optional coin cell battery for RTC and LED on ALARM output (coin cell not included)
Other
• OEM Board current measuring
• Parallel NOR flash on external memory bus
• 16-bit register and LEDs on external memory bus
• 5-key joystick
• 3-axis accelerometer (I2C connected)
• LM75 temperature sensor (I2C connected)
• 5 push-button keys (four via I2C and one on ISP-ENABLE)
• 9 LEDs (8 via I2C and one on ISP-ENABLE)
• Trimming potentiometer to analog input
• USB-to-serial bridge on UART #0 (FT232R) and ISP functionality
• Reset push-button and LED
• Speaker output on analog output from OEM Board, or from I2S audio codec
• 160x150 mm in size
The LPC1788 Developer's Kit is an Evaluation product not designed for integration or long time availability. The LPC1788 OEM Board is however an Integration product
Documentation and Resources
The following resources are available for download either directly below or from our support site after registration of the LPC1788 Developer's Kit.
Segger has created an evaluation software package with emFile, emWin, embOS, embOS/IP, emUSB Host, emUSB Device. Projects files for Keil MDK V4.22 and IAR EWARM v6.20/21 are supported.
The application auto detects which LCD (3.2 inch, 4.3 inch or 7 inch) that is connected and adjusts LCD parameters accordingly.
There is an update of one file (LCDConf.c - located under \Start\Setup). The update fixes an issue with the touch screen on the 7 inch LCD. Unzip this file at this location and rename it to LCDConf.c (overwriting the files supplied by Segger). Then recompile the Segger project.
