Price

179€

Art. EA-OEM-411

LPC3250 Developer's Kit v2

Embedded Artists' LPC3250 Developer's Kit lets you get up-and-running quickly with the LPC3250 OEM Board. The LPC3250 OEM Board is equipped with NXP's ARM926EJ-S based LPC3250 microcontroller suitable for applications that require high performance, high integration, and low power consumption.

The LPC3250 OEM Board is using LPC3250 MCU rev A.

The Kit is perfect for running Linux with its large on-board RAM and Flash, network and graphics capabilities.

Focus on your value-added application by using this Developer's Kit as your prototyping platform. It includes the software components needed to get up-and-running with your software development on day 1.

When you are finished with prototyping and/or evaluation you can easily transfer your application and the OEM Board into production.

Display Options

Note that display options are sold separately

4.3 inch TFT LCD with touch - via LPC3250 on-chip LCD controller
7.0 inch TFT LCD with touch - via LPC3520 on-chip LCD controller
Display Expansion Board, HDMI/DVI/VGA/LVDS - via LPC3250 on-chip LCD controller
1.35 inch Memory LCD - via Serial Expansion Connector
1.5 inch RGB OLED - via Serial Expansion Connector
2.7 inch E-paper display - via Serial Expansion Connector

Unpacking

Specification

LPC3250 OEM Board

Processor	NXP's ARM926EJ-S LPC3250 microcontroller in BGA package
External Flash	128 MB NAND FLASH (1Gbit) 4 MB SPI-NOR FLASH (32Mbit)
Data Memory	64 MB DDR SDRAM + 256 KB internal 16-bit data bus to DDR SDRAM
Ethernet	100/10M Ethernet interface based on National DP83848 Ethernet PHY
Clock Crystals	13.000 MHz crystal for CPU
Dimensions	66 x 48 mm
Power	3.15V-3.3V powering
Connectors	200 pos expansion connector (as defined in SODIMM standard), 0.6mm pitch
Other	• 256 Kbit I2C E2PROM for storing non-volatile parameters • 5 LEDs • Buffered 16-bit databus

OEM Base Board

Connectors and Interfaces	• 200 pos, 0.6mm pitch SODIMM connector for OEM Board • LCD expansion connector with control signals for touch screen interface • Expansion connector with all OEM Board signals • Ethernet connector (RJ45) • CAN interface & connector (provision for second CAN interface, but not mounted) • MMC/SD interface & connector • USB1: OTG or Host interface & connector • USB2: Device or Host interface & connector • Provision for NXP JN5148 RF module (former Jennic) interface (RF module not included) • Full modem RS232 (cannot be fully used on 32-bit databus OEM boards) • RS422/485 interface & connector • Provision for IrDA transceiver interface (transceiver not mounted) • I2S audio codec (mic in, line in, line out, headphone out) • SWD/JTAG connector • Trace connector and pads for ETM connector • Serial Expansion Connector, 14-pos connector with UART/I2C/SPI/GPIO pins
Power	• Power supply, either via USB or external 5V DC • Optional coin cell battery for RTC and LED on ALARM output (coin cell not included)
Other	• OEM Board current measuring • Parallel NOR flash on external memory bus • 16-bit register and LEDs on external memory bus • 5-key joystick • 3-axis accelerometer (I2C connected) • LM75 temperature sensor (I2C connected) • 5 push-button keys (four via I2C and one on ISP-ENABLE) • 9 LEDs (8 via I2C and one on ISP-ENABLE) • Trimming potentiometer to analog input • USB-to-serial bridge on UART #0 (FT232R) and ISP functionality • Reset push-button and LED • Speaker output on analog output from OEM Board, or from I2S audio codec • 160x150 mm in size

The LPC3250 Developer's Kit V2 is an Evaluation product not designed for integration or long time availability.
The LPC3250 OEM Board is however an Integration product

Documentation and Resources

The following resources are available for download either directly below or from our support site after registration of the LPC3250 Developer's Kit.

Documents

User's Manual
LPC3250 OEM Board Datasheet
LPC3250 OEM Board Measurements
OEM Base Board Measurements
OEM Board Make or Buy Analysis
OEM Board Integration Guide
LPC3250 OEM Board Schematics (Login required)
OEM Base Board Schematics (Login required)
Linux BSP Manual (Login required)
CE Declaration of Conformity
Embedded Artists' general RoHS 2 declaration

Product Change Note (PCN)

NAND change (2014-12-20)

Software

Sample Software Disclaimer

NXP's Common Driver Library (CDL) framework has been used to develop a number of sample applications for the LPC3250 OEM Board. The main IDE is Keil's MDK-ARM which is the only one being tested by Embedded Artists. NXP's CDL package also supports CodeSourcery GCC and IAR Embedded Workbench.

ADC - an example using interrupts to measure ADC channels 0, 1 and 2
Ethernet - A polled Ping application that illustrates the usage of the Ethernet interface
Kickstart - A simple bootloader stored in block 0 of the NAND flash loading an application stored in block 1 an onwards.
LCD - An application using NXP's SWIM library to draw some color bars on the QVGA LCD display
NAND Programmer - This application programs the NAND flash with the kickstart application in block 0 and a second application, for example, the S1L application in block 1 and onwards.
RTC An example using the Real-Time Clock to generate TICK events
S1L - A more complex bootloader that allows you to load applications from several sources such as the NAND flash, serial port or MMC/SD card.

SD/MMC - A sample application using the memory card interface
SLC NAND - An application that is using the Single-Level NAND controller to read and write data to the NAND flash.
SPI NOR - This application illustrates how to read and write data to the NOR Flash.
Timer - A simple example using the timer interface
Touch Screen - This application first runs a calibration sequence and then uses NXP's SWIM library to let you draw on the display using the touch screen.
UART - A simple example illustrating how to use the UART

External Resources